Buildex®   One of the world's leading manufacturers and suppliers of self-drilling screws and fasteners.
Corporate Profile Latest News Products New Products Real World Performance Buildex Suport Export Department Contact Buildex
WingTEKS® Home > International > WingTeks®
Download this page
Overview
Composite Panel Teks®
Roofing & Cladding Screws
Steel House Framing Screws
WingTeks®
SuperTeks® Series 500
FibreTeks®
Standard Teks®
Stainless Steel
AutoTeks®
Headlok®
PolyZIPS® / Fibreglass Teks®
Tapcon®
Wall Mates®
Sockets & Drive Bits
Washers & Cyclone Plates
Multi-Grip Rivets
WingTeks®

The revolutionary Buildex® WingTeks® range now have a new wing design, making them even quicker and easier to install.

They are available in our exclusive Climacoat® 3 finish, providing greater protection in treated timbers. WingTeks® are specially designed to enable the fastener to fix timber to metal without the timber rising to the top of the screw while the metal is being drilled.
WingTeks®

Coating
 
Climacoat® 3
   
   
   

How To Use
1. Measure the thickness of materials to be fastened including the air gap.
2. Select correct size drive bit
6, 8 & 10 gauge #2 Cross Recess Bit
14 gauge #3 Cross Recess Bit
3. Fit driver to a power screwdriver set to high approx. 2500rpm (Driving too slowly may result in the wings not breaking off. The hole will be too large and the thread won’t hold). Note. 14g screws set driver speed to 0-1000rpm.
4. Place WingTeks® on the driver bit, place at fastening position and push sharply to create a starting point.
5. Squeeze screwdriver trigger and maintain firm end pressure until the WingTeks® has drilled and fastened.

  Countersunk Rib Head - Wing Teks®
  For fixing timber floors, fences and composite boards to steel 1.0 – 6.4mm
(Check table below for screw size drill capacity).

Click to view video




Countersunk Rib Head - Wing Teks®
Gauge T.P.I / Length Pack / Carton Qty Pallet Qty Part Number
3.5mm / 6g 20 x 50 1000 / 3 216,000 6-321-0045-8CC
4.2mm / 8g 18 x 35 1000 / 4 288,000 6-321-0041-5CC
4.8mm / 10g 16 x 40 500 / 4 144,000 6-321-0057-9CC
  (with reduced head size 8mm)    
  16 x 45 500 / 4 144,000 6-321-0040-7CC
  16 x 55 1000 105,000 6-321-0042-3CC
  16 x 75 1000 84,000 6-321-0043-1CC
6.3mm / 14g 20 x 65 500 52,000 6-321-0058-7CC
Important note: WingTeks® are not recommended for use in Decking applications.

  Technical Specifications (kN = Kilo Newtons, nM = Newton Metres)
Screw Size Max Timber Thickness Wing Drill Capacity Max Rec Drill Type
3.5mm / 6-20 x 50mm 37mm 1.0 - 2.3mm 350 - 550W
4.2mm / 8-18 x 35mm 20mm 1.0 - 2.5mm 350 - 550W
4.8mm / 10-16 x 40mm 22mm 1.2 - 3.5mm 350 - 550W
4.8mm / 10-16 x 45mm 27mm 1.2 - 3.5mm 350 - 550W
4.8mm / 10-16 x 55mm 37mm 1.2 - 3.5mm 350 - 550W
4.8mm / 10-16 x 75mm 57mm 1.2 - 3.5mm 350 - 550W
6.3mm / 14-20 x 65mm 41mm 2.0 - 6.4mm 700 - 900W

  Technical Specifications (kN = Kilo Newtons, nM = Newton Metres)
Screw Gauge T.P.I Single Shear (kN) Axial Tensile (kN) Torsional Strength (Nm)
3.5mm / 6g 20 3.5 4.3 3.5
4.2mm / 8g 18 5.1 6.3 5.9
4.8mm / 10g 16 6.8 11.9 8.4
6.3mm / 14g 20 11.2 21.2 20.4

Values given are averages obtained under laboratory conditions.
Appropriate safety factors should be applied for design purposes.



YOU ARE HERE:
Home > International > WingTeks®
Supply Terms & Conditions

|

Copyright 2017 ITW BUILDEX